Slow Speed Weigh in Motion

The MVR Series of In-Motion Vehicle Scale offers the ideal combination of accuracy and speed. The In-Motion Scale uses a fully welded steel structure contained within a single framework. This rugged platform is supported by four DESB-DBA Series Load Cells to weigh each axle end of a vehicle as it travels across the scale. The weighing platform is approximately 3000mm in width and 750mm in length and is constructed of smooth finish HT grade steel plate. The welded steel structure is designed with performance and longevity in mind.

The extremely stiff and rigid weighbridge, coupled with four 20,000 kg capacity load cells, results in a higher resonant frequency allowing more efficient filtering of spurious weight signals.

Indicator

The MVR Weight Indicator for In-Motion Vehicle Scale offers the ideal combination of accuracy and speed.

  • GLCD display with four keys on the front panel of eldon MS box.
  • Serial strings for communication as per your requirement.
  • Logic with two loops and one IRS (pnp) type.
  • MVR will supply two parallel sensing Light curtains with each controller.
  • The Light curtains will installed in a box near WIM along with junction box by MVR
  • A power supply of 24V to drive IRS.
  • LEDs on mother board for loop sensors and IRS.
  • This is low speed (max speed 20 kmph) system with accuracy of 2-4% of fsc and depends on the level of section before and after weighing zone.

Key Benefits

  • High vehicle throughput
  • Maximize operational Productivity and cost savings
  • Gross weight, axle weights, numbers of axles can be recorded along with average speed
  • Suitable for overload detection, statistic data collection, road maintenance planning etc.

Technical Specifications (Slow Speed WIM)

Details
Capacity User Selectable
Stationary Accuracy ±0.05% FSR* (depends on field conditions, installation, structure and load cells also)
In-Motion Accuracy with respect to Speed ±1-3% FSR up to speed of 20 km/hr (depends on field conditions, installation, structure and loadcells also)
Type of In motion scale Load cell based permanent In-motion scale.
Operational Temperature 0˚C to 50˚C
Power supply AC single Phase 230V, 50 Hz

Load Cells

MVR LC’S are double ended shear beam load cell ideally suited for Truck, track, onboard weighing applications. Its construction of high alloy tool steel provides optimum protection under impact loading & adverse conditions. The cell is environmentally protected with waterproof seal and is Electro less nickel plated to assure resistance against corrosion.

Performance Specification
Standard Capacity 10,15,20,22.5,25 Tf
Excitation Voltage 10 VDC- Maximum 15 VDC
Nominal Output 2.0 m V/ V
Non - Linearity < ±0.1% FSO (Full Scale Output)
Hysteresis < ±0.15% FSO
Non-Repeatability < ±0.1% FSO
Creep (30 minutes) < ±0.02% FSO
Zero Balance ±1.0% FSO
Input Resistance 770 ± 15 Ohms
Output Resistance 700 ± 5 Ohms
Insulation Resistance (50 VDC) > 1000 Mega Ohms
Certification CE Certified
Safe Overload of Rated Capacity 150%
Ultimate Overload of Rated Capacity 300%
Temp. Compensated Range 0-500C
Temperature Effect on Output < 0.01% FSO/ 0C
Temperature Effect on Zero < 0.01% FSO/ 0C
Deflection < 0.4 mm at FSO
Finish & Construction Electroless Nickel Plated Tool Steel

Surge Protector / Junction Box

MVR Technology has introduced a Lightning protection Junction box for Analog & Digital load cell with better protection against lightning and high voltage Surge. Special components to enhance protection against Lightning Strikes have been incorporated. This will enhance performance, reduce down time and reduce field calls for WIM installations using DESB Load cells..

IR LIGHT CURTAINS(FROS)

Specifications
Power Supply 12 - 24 Volts DC
Supply Protection Reverse Polarity Protected
Output PNP or NPN / NO or NC
Output Indications Through LEDs
Channel Indication LED indication for each channel
Response Time On to Off : 10 - 15 m.sec. Off to On : 50 - 100 m.sec
No of Beams 4, 6, 8, 10 , 16, 20, 16, 24, 32, 40, 48, 56, 64
Beam bypass Provided in hand/body protection models
Protected Heights 90 - 2000 mm
Pitch offered 11, 20, 30,40, 50, 90mm
Adjustable Range Up to 3 meters (Higher range up to 40 meters available)
Standard Cable length 5 meters for emitter, 3 meters for receiver
Operating Temperature Up to 55 Degrees centigrade
Cross Section 36 x 42 mm
Electrical Connections Plug in Connector for Emitter & Receiver
Applicable to Directly work with PLCs / Controllers
Protections Output short circuit protected
Vibration Resistance Amplitude: 0.75 mm (p) Freq : 10 - 55 Hzs, Rate : 1 Octave / min
Operating Light 500 Lux (max.) when source is places opposite to receiver, > 3000 lux when source placed at an angle of 20 degrees

MVR WIM FEAUTRES

  • Optimal pricing
  • Quick and trouble free installation
  • High vehicle throughput
  • Maximize operational Productivity and cost savings
  • Automatic vehicle counter and immediate indication of the vehicle overload
  • Dust and waterproof wirings for easy and reliable connection
  • Gross weight, axle weights, numbers of axles can be recorded along with average speed
  • Data records can be stored for future use or can be sent via LAN or Internet to the server